Smart home System ►   Automation | Burglar Alarm | Sound Diffusion | Temperature Control | Communication | CCTV System | Onile Simulationy

■ Burglar Alarm

HC4601 control unit with system self-learning function and display of the

HS4601 configuration on the screen. Controlled using the transponder and

the keypad. Managing up to 36 sensors and 4 zones. Possibility to

set up to 4 scenarios. Fitted with alarm signalling actuator, as well

as doors and windows protection NC contacts connection terminal.

Wall mounting using the metal bracket supplied as standard.

Battery powered, using supplied battery item L4380/B.

HC4606 device for arming or disarming the system using a numeric key, set

HS4606 and saved on the burglar-alarm control unit, item. 3485, item

3486 and item HC/HS4601

HC4603/4 receiver to switch the system on and off by means of the remote

HS4603/4 control – pushbuttons to control 4 zones – signals the state of the

zones and the system by leds – can disable the light and sound signals.

HC4607/4 subdivider as above - used for enabling/disabling the system with

HS4607/4 transponder, item 3530S and item 3540

HC4603/8 module to extend the zones which can be divided – pushbuttons

HS4603/8 to control zones 5 – 8 – leds signal the state of the zones – can

disable the light signals

HC4604 receiver to switch the system on and off by means of the remote

HS4604 control – signals the system state by leds – can disable the light

and sound signals – can set the activation of fixed zones of the

system – auxiliary channel available for actuations. Use only with

control unit item 3486.

HC4605 module to switch the system off and block it by means of a

HS4605 mechanical key - signals the system state by leds – fitted with

keyhole cover – key with 10,000 combinations

HC4607 switches the system on and off by means of the transponder

HS4607 (badge) – can save up to 30 transponders - leds signal the system

state – auxiliary channel available for actuations

3486 control unit as above. Controlled using the IR remote control, the

transponder and the keypad. Fitted with integrated PSTM and GSM

telephone dialling device, for forwarding of alarms. Wall mounting

using the metal bracket supplied as standard, or flush mounting in

MULTIBOX units. Battery powered, using battery item 3507/6.

3485 POLYX ALARM control unit with system self-learning function and display

of the configuration on the screen. Controlled using transponder

and the keypad. Managing up to 72 sensors and 8 zones. Possibility

to set up to 16 scenarios. Fitted with PSTM telephone dialling device

for forwarding of alarms. Programmed using the TiSecurity application.

Wall mounting using the metal bracket supplied as standard.

Battery powered, using battery item 3506, supplied as standard

TIMED AUTOMATIC SWITCHING ON/ OF

THE ENTRANCE LIGHTS AFTER SWITCHING OFF

THE BURGLAR-ALARM SYSTEM

3530S thin portable badge

3540 key-ring portable badge

4050 portable infrared-ray remote control to switch the system on and off – can be automatically coded by means of the central unit – power supply by means of two lithium batteries supplied – life 50,000 operations

■  IR Passive Detectors

HC4610 volumetric presence detector with passive infrared rays with

HS4610 adjustable sensitivity level (3 to 9 metres) - alarm signal LED

with memory - angular opening 105°, 14 bands divided over 3

levels – auxiliary prealarm channel can be activated

HC4611 volumetric presence detector as above – angular opening can be

HS4611 divided from 105° to 0°– swivel lens on 2 axes

HC4613 dual-technology volumetric presence detector made up of two

HS4613 sensors: one infrared to detect hot bodies (IR) and one with

microwaves to detect movement (MW). The alarm is only triggered

when both detection technologies activate.

HC4612 NC electromagnetic contact interface module – can connect

HS4612 balanced and unbalanced contact protection line – alarm indication

LED with operation memory – auxiliary prealarm channel can be Activated

HC4612/12 Interface module for cable detector to protect shutter – can be

HS4612/12 applied to NC/NO and window-breaking detectors (Item 3516).

N4640 volumetric presence detector with passive infrared rays with

adjustable sensitivity (3 to 9 metres) – alarm signal LED with

memory – range max. 9 metres, angular opening 105°, 14 bands

divided over 3 levels – auxiliary prea arm channel can be activated – assembly on the wall, inclined and at an angle

■  Other Detectors

3510 NC electromagnetic contact interface detectors and protection line

– version for flush mounting

3510M detector as above – brass, high mechanical resistance - used for

non-ferromagnetic window and door frames with a low section

profile

3510PB detector as above – brass, high mechanical resistance - used for all

types of window and door frames and armored doors.

3512 NC electromagnetic contact interface detectors and protection line

– version for flush mounting – die-cast aluminum for swing door or sliding

door installations. For floor installations.

3513 detector as above – version for visible mounting for metal surfaces

3514 detector to protect rolling shutters or similar winding shutters – can

also manage an opening magnet (supplied) to check the perimeter

3516 piezoelectric window-breaking detector. Installation by means of

double-sided adhesive tape supplied.

3518/50 active infrared barriers, to protect windows and doors.
The deviceis made up of 2 columns, one acts as TRANSMITTER (TX), the other as RECEIVER (RX). When several IR beams are broken the alarm is immediately triggered - 58 cm
3518 barrier for windows - 108 cm
3518/150 barrier for windows - 158 cm
3519 barrier for doors - 208 cm

■  Radio Extension

HC4618 radio receiver module to be used as interface between the wire

HS4618 burglar-alarm and the radio sensors to make combined wire-radio

systems – can also be used for remote assistance functions

together with remote control item 3448 and radio detectors.

3448 radio remote control to send remote assistance signals – it can be

programmed automatically using the HC/HS4618 radio receiver -

powered by 3V CR2032 type battery supplied as standard - battery life 2 years.

348220 dual pushbutton radio remote control for arming or disarming the

system. Maximum distance 50 m without ob tructions. Powered

by a CR2032 3V type battery. To be used with radio receiver, item

HC/HS4618.

3440 volumetric presence detector with passive infrared rays – alarm LED

– output 13 metres, angular opening 90°, 17 beams divided over

4 levels – impulse-count function can be fi tted - supplied with 1

battery 3.6V type AA supplied

3442 magnetic opening detector for doors and windows – can be connected with extra magnetic wire contacts (Items 3510, 3511 and 3513) – supplied with 1 battery 3.6V type 1/2 AA not supplied.

3444 piezoelectric detector to check windows – radius of coverage 1.5

metres- supplied with 1 battery.

■  Cable Radio Detector for Rolling Shutters

3445 detector to protect rolling shutters or similar winding shutters,

made of a rope sensor and radio transmitter - can also manage an

opening magnet (supplied) to check the perimeter - supplied with

1 battery.

■  Flood Detectors

HA4619 detector with sensor, for detecting flooding caused by any type of

HS4619 liquids – supplied with 3V CR2032 alkaline battery as standard.

To be fitted with front cover plate and key covers items HC4919

and HS4919.

3482 water detection sensor - to be used together with the contact

interface item 3480, in technical alarm mode.

■  Internal Siren

HC4070 self-supplied internal siren can be installed in box 506E to be

HS4070 fitted with 6V 0.5Ah battery Item 3507/6 – sound intensity 90dB(A)

at 3 meters – protected against pulling off and tampering

■  External Siren

4072L external siren which contains the self-supply battery for the whole system – sound signalling can be set from 0 to 10 minutes by means of the control unit – to be fitted with 12V 12Ah battery Item 3505/12 – sound intensity 105dB(A) at 3 metres – light signaller with xenon lamp – anti-foam grid – protected against being pulled off and opened – to be used with power supply Item E46ADCN
 

4072A self-supplied external siren – sound signalling can be set from 0 to 10 minutes by means of the control unit (1 or 4-zone) – to be fitted
with 12V 7Ah battery – sound intensity 105dB(A) at 3 metres – light signaller with xenon lamp – anti-foam grid – protected against being pulled off and opened – to be used with power supply Item E47ADCN